| Desarrollador: | Precitec GmbH & Co. KG (3) | ||
| Precio: | Gratis | ||
| Clasificaciones: | 0 | ||
| Opiniones: | 0 Escribir una opinión | ||
| Comentarios: | 0 Publicar comentario | ||
| Listas: | 0 + 0 | ||
| Puntos: | 0 + 0 ¡ | ||
| Google Play | |||
Descripción
• Connection: shows active Bluetooth devices in the network
• Temperature: shows the sensor values of the four temperature sensors
• Pressure: shows cutting gas pressure and purging air pressure
• Optics: looks different, because of different laser head types
- Normal: focal positions, potentiometer offset, diffused light, lens configuration.
- ZoomCutter: aspect ratio replaces the lens configuration.
- Manual: just diffused light is shown.
• Errors: shows active error messages. If no error exists, the screen is empty.
• IO: shows the IO-interface, with analogue voltages, currents and signals.
• System: laser head firmware version and serial number.
Besides, in the system window there is a button. This button starts the record of the measurement values. The measurement values are stored in a *.csv file, which is created in the memory of the used device. The App has two access modes, USER and OEM. The determination is regulated through two different PINs. Users with USER-rights can define the memory location and the sampling rate of the .csv file. Besides the USER can change his own PIN. The OEM can additionally configure thresholds for the laser head. Furthermore the OEM can change his own and the USER-PIN.
The functionality of the app could be restricted, because of different laser head firmware versions. The IO window is not supported with firmware lower than 2.0.0. Also the one-time PIN algorithm is not supported for firmware versions below 2.0.3. With this algorithm a one-time change of your PIN is possible, when the PIN was forgotten or wrong entered.
The App works just as a display when the laser head is connected through CAN. It is not possible to change any thresholds with the App and the IO window is hidden.
The manuals in English and German versions are delivered in the pdf-format within the app. During the first start of the app, after approving the GTC, both versions of the manuals will be stored in the download-section of the used device. Besides it is possible to open the manual in the settings of the app. Depending on the used language in the device the German or English version will be shown. To display the manuals a pdf-viewer is required.
Ad
Capturas...
Novedades
- Versión: 3.3.7
- Actualizado:
Historial de precios
- Hoy: Gratis
- Mínimo: Gratis
- Máximo: Gratis
Realizar un seguimiento de los precios
Ad
Desarrollador
- Precitec GmbH & Co. KG
- Plataformas: Android Aplicaciones (3)
- Listas: 0 + 0
- Puntos: 0 + 0 ¡
- Clasificaciones: 0
- Opiniones: 0
- Comentarios: 0
- Descuentos: 0
- Vídeos: 0
- RSS: Suscribirse
Puntos (0)
0 ☹️
Clasificaciones (0)
0 ☹️
Listas (0)
0 ☹️
- Precitec ProCutter
Opiniones (0)
Sé el primero en escribir una reseña 🌟
Comentarios (0)
Sé el primero en comentar 🌟
Información adicional
- Versión: 3.3.7
- Categoría:
Android Aplicaciones›Herramientas - Sistemas operativos:
Android 6.0 - Tamaño:
23 Mb - Clasificación de contenido:
Everyone - Google Play Puntuación:
0 - Actualizado:
- Fecha de lanzamiento:
Contactos
- Sitio:
http://www.precitec.de
«Precitec ProCutter». Plataforma: Android. Categoría: Herramientas. Desarrollador: «Precitec GmbH & Co. KG». Primer lanzamiento: . Última actualización: . Precio actual: gratis. Este título aún no ha recibido calificaciones ni reseñas en AppAgg. AppAgg rastrea el historial de precios, las calificaciones y los comentarios de los usuarios para «Precitec ProCutter». Siga futuros descuentos y actualizaciones a través de RSS. AppAgg no aloja aplicaciones ni distribuye software. Todas las marcas comerciales, logotipos y capturas de pantalla pertenecen a sus respectivos propietarios.
Precitec ProCutter URL corta: Copiado!- 🌟 Compartir
- Google Play
También te puede interesar
-
- Precitec ProCutter 2.0 Firmwar
- Android Aplicaciones: Herramientas De: Precitec GmbH & Co. KG
- Gratis
- Listas: 0 + 0 Clasificaciones: 0 Opiniones: 0
- Puntos: 0 + 0 Comentarios: 0 Versión: 2.0.5 The Firmware Update App is used to update ProCutter Standard and ProCutter ZOOM using an encrypted firmaware file. The connection is via WLAN and has the same requirements as the ... ⥯
-
- Precitec ProCutter 2.0
- Android Aplicaciones: Herramientas De: Precitec GmbH & Co. KG
- Gratis
- Listas: 0 + 0 Clasificaciones: 0 Opiniones: 0
- Puntos: 0 + 0 Comentarios: 0 Versión: 2.2.3 The Precitec ProCutter 2.0 App is used to visualize the state of the laser head during operation, to query error messages and to set the customer offset. Optionally, the app can also ... ⥯